Directed Electronics 4-button series Manuale delle Istruzioni Scaricare il pdf (Pagina 37)

Red: +12V

Black: Ground

Fuse

Not used here:

D2D (4 pin, wht)

ESP (3 pin, blk)

ESP (4 pin, brn)

2 pin

4 pin

5 pin (see table below)

Conguration wires

Gray & White

+12V

GND

D2D

(4 pin, white)

2 pin

4 pin

cut loop (see table)

✂

CPU1

NOTE: The appearance and connector/port

arrangement on the Directed/Avital/Xpresskit

system may dier to the examples shown .

SmartStart Module

(Top view)

SmartStart Module to Xpresskit

Directed System

(Top view)

LED

Installation Procedure

This product is compatible with most Directed Elec-

tronics Security, Remote Start and hybrid systems that

are ESP2 compatible (3 or 4-pin). Non-compatible

systems include 3001L and older AM1/AM5 mod-

els.

Please read the following before proceeding

1. Customer Information required:

• Record the customer information requested

in step 4a of this procedure. The module ID

# is provided on a sticker which can be af-

ﬁxed to the space provided in step 4a.

This information is required for ﬁnal veriﬁ-

cation/activation of the VSM200/250 or

DSM200/250.

2. Installation Points:

• Install and test the security/remote start sys-

tem ﬁrst using the associated guides and

wiring diagram. If using an existing system,

verify it is fully functional before installing the

Directed SmartStart module.

• For 3000-series or standalone SmartStart

systems with no remote control, test the in-

stalled system via the SmartStart activation

portal.

• Mount the SmartStart module as high as pos-

sible in the vehicle (the engraved side faces

up for GPS devices). Mount with minimal

obstructions that can affect communications

and within reach of the main Directed system

using the provided cables (do not extend).

The module's signal strength (RSSI) can be viewed in the

activation portal after a successful transmission test.

-50 to -90 dB

-91 to -100 dB

> -100 dB

= good signal strength

= borderline/inconsistent signal strength

= weak, insufﬁcient signal strength

• DO NOT connect the SmartStart module un-

til the ﬁnal programming of the Remote Start

main unit and veriﬁcation of security/remote

start system operations are completed.

CAUTIONS

The white plug is ONLY for RSR (Remote Start

Ready) and RXT applications using certain Xpresskit

interfaces (go to www.xpresskit.com for details on

supported devices & vehicles).

For systems with combined 4-pin ESP/D2D ports,

you CANNOT use an interface module in D2D

mode when using a SmartStart module. You must

use W2W on the bypass module.

DO NOT connect the black 3-pin ESP connector to

white Door Lock port on Directed systems.

There should NEVER be more than one data plug

connected from the 3-way harness.

QRNDSM250 2011-10

5-pin Cable

Pin # Wire Color Connection/Description

1 White/Blue

(-) RS (Remote Start)/AUX output

2 Brown

(-) Factory horn/Alert input

3 Green

(-) Lock

4 Blue

(-) Unlock

5 Red/White

(-) Trunk/AUX output

Note: The analog output wires are only active if the device has

been conﬁgured for Analog Wire mode in the installation portal.

Quick Reference

Install Guide

VSM200/250, DSM200/250

Wiring Schematic

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 46 47

Commenti su questo manuale

Nessun commento

Directed Electronics 4-button series Manuale delle Istruzioni Pagina 37

Commenti su questo manuale

Prodotti e manuali riguardandi Alarme antifurto per auto Directed Electronics 4-button series