Directed Electronics D2400 Manuale Utente

Army TB 11-5820-1130-10-1 Air Force TO 31R2-2PSC5-8-1 TECHNICAL BULLETIN OPERATOR’S GUIDE RADIO SET, AN/PSC-5 (SPITFIRE) (NSN 5820-01-366-4120) (EIC

8 Use the following section to assist in configuring the KL-43 to interface with the AN/PSC-5. Use the W1 cable between P2 of KL-43 to Aux Connecto

9Table 2 ViaSat Recommended Settings (PDC ViaSat V-eMail with PDC-400 card via User provided cable between PDC card and Aux Connector of AN/PSC

10 Use the following procedure as an alternate method of obtaining ViaSat Recommended Settings: 1. When first accessing, go to Setup and then User

11Perform the following to load terminal data. NOTE: Current mode must be LOS to change the terminal address. 1. Press ESC until the main menu is

12 Perform the following to enter satellite ephemeris data, which is required for passive ranging. 1. Press ESC until the main menu is displayed.

13Use the list below as a reference of data required for 5-kHz DAMA. If you are missing any of the information, contact your supervisor. Table 3

14 Guard List {9} 1:____ 2:____ 3: ____ 4:____ 5:____ 6:_____ 7: ____ 8:____ 9:____ 10:____ 11:____ 12:____ 13:____ 14:____ 15:____ Demarcatio

15Perform the following to select 5-kHz I/O rates. 1. Press ESC until the main menu is displayed. 2. Press 2. (Database Options) 3. Press 4.

16 The guard list is a set of addresses for which a terminal receives services (do not enter your terminal address). The guard number is the addres

17Perform the following procedure to enter a DAMA preset. 1. Press ESC until the main menu is displayed. 2. Press 3. (Set Presets) 3. Press 1.

Page # Page # Table of Contents Guard List 35 List of Tables 1 25-kHz DAMA Preset(s) 36 Introduction 2 25-kHz DAMA Service Preset(

18 Perform the following procedure to enter a 5-kHz Service preset. 1. Press ESC until the main menu is displayed. 2. Press 3. (Set Presets) 3.

19 Perform the following to enter a 5-kHz Message preset. 1. Press ESC until the main menu is displayed. 2. Press 3. (Set Presets) 3. Press 4.

20 This page intentionally left blank.

21Perform the following to quickly start a 5-kHz DAMA network service. 1. SELECT DAMA. 2. ENTER preset (even if already displayed). CURRENT MODE D

22 Table 6 5-kHz DAMA Hot Keys # FUNCTION 1 Service Setup. Provides controller with information on the type of service requested in order

23Perform the following to manually setup a 5 kHz DAMA network. 1. SELECT DAMA. 2. ENTER preset (even if already displayed). CURRENT MODE DAMA -P

24 NOTE: Ensure current service state is idle (SRV-Idle). Circuit/DASA Service Setup. Hot Key #1. a. ENTER on preset number 00 for manual

25Send a Message. Hot Key #8. a. Ensure service is idle. SELECT XMIT. The display will indicate how many messages are in the queue. MESSAGE QUEU

26 Teardown. Hot Key #2. Hot Key #1 for DASA. a. SELECT service (# / #) to teardown. b. VIEW DESTIN or SOURCE address. ENTER. c. Press ENT on

27Table 7 Service Assigned Errors and Warnings MESSAGE ACTION Verify I/O Device a. ERROR. Attach asynchronous data device and accept service

1Table # Table Title Page # 1 KL-43 Recommended Settings 8 2 ViaSat Recommended Settings 9 3 5-kHz DAMA Checklist 13,14 4 5-kHz DAMA I/O Da

28 Table 9 5-kHz DAMA Messages MESSAGE ACTION A Acquisition Failed Your terminal is not receiving OW. Check azimuth, power out and repositio

29 C Circuit Setup Rejected (Reason) Service request is denied for the stated reason. Try again later unless one of the reasons

30 L Logged Out (Reason) The controller has logged your terminal off the network for the reason supplied. Correct the error and perform an Over

31 MESSAGE Input Rejected Transmission rejected. Someone else is transmitting - try again later. Or, radio is in idle – set up a service. Output

32 This page intentionally left blank.

33Use the list below as a reference of data required for 25-kHz DAMA. If you are missing any of the information, contact your supervisor. Table 10

34 Terminal Address {8} ________ (00000-65535) Guard List {9} Up to fifteen five-digit addresses COMSEC Key 1-6 Orderwire Key 1-4 Call Precede

35 The guard list is a set of addresses for which a terminal receives services (do not enter your terminal address). The guard number is the address

36 Perform the following procedure to enter a DAMA preset. 1. Press ESC until the main menu is displayed. 2. Press 3. (Set Presets) 3. Press 1.

37 Perform the following to enter a 25-kHz AC Service preset. 1. Press ESC until the main menu is displayed. 2. Press 3. (Set Presets) 3. Press

2 SCOPE This manual is a quick reference guide for trained users of Radio Set, AN/PSC-5. Refer to TM 11-5820-1130-12&P for more detailed inst

38 Perform the following to quickly start a 25-kHz DAMA service. 1. SELECT DAMA. 2. ENTER preset (even if already displayed). CURRENT MODE DAMA

39Table 12 25-kHz AC DAMA Hot Keys # FUNCTION SCREEN 1 Service Setup. Provides controller with information on the type of service requested

40 Service Setup. Hot Key #1. a. ENTER on preset number 00 for manual service setup. Otherwise ENTER the service preset number and proceed to

41 Teardown. Hot Key #2. (Hot Key #1 for DASA.) a. Press ENT on SEND. The network menu will indicate Idle when complete. TEARDOWN {SEND} Data

42 Paging. Hot Key #9. a. ENTER up to three terminal addresses to page. b. Press ENT on SEND. {17} PAGING #####, #####, ##### {SE

43 Table 13 25-kHz DAMA Messages MESSAGE ACTION C Call Waiting Party: #### Prec Routine You have been paged – notify the sender that you rec

44 P Paging Request (Result) Displays result of request to suspend temporarily service. No action required unless noted below. Denied. Request

45Table 14 Information Request Codes Please note: wherever it states contact the NCTAMS – the RSSCs may be contacted and can provide you as

46 69 Terminal ID duplicates an existing operational address. The requesting terminal’s ID duplicates the address of an operational controller. Yo

4774 Requested terminal is already connected to a DASA service. The requested user is on a terminal that is already connected to a DASA service, and

3The following procedure covers using the AN/CYZ-10 with CT3 Software to load COMSEC variables. See TM 11-5820-1130-12&P for other devices. NOT

48 80 Enter a Configuration Code and try again. The terminal operator has not entered a Configuration Code into the port originating the request sin

49 87 Requested party’s terminal is unauthorized or zeroized. The requested user is on a terminal that is marked in the controller database as in a

50 92 Not all requested parties could be connected. At least one, but not all, of the requested parties could be connected. (This request is ho

5195 DASA requests are reserved for guards only. The requesting user’s Configuration Code indicates a DASA service and the user has requested conne

52 CONFIGURATION CODES Configuration codes identify to the control station the baseband equipment attached to the terminal I/O port. Currently, th

53The following tables list some of the status messages that may be displayed during DAMA operation. See TM 11-5820-1130-12&P for a complete li

54 This page intentionally left blank.

55Perform the following procedure to enter Line of Sight (LOS) preset(s). 1. Press ESC until the main menu is displayed. 2. Press 3. (Set Presets

56 Perform the following procedure to enter a SATCOM preset(s). 1. Press ESC until the main menu is displayed. 2. ENTER 3. (Set Presets) 3. E

57Perform the following procedure to set up a satellite relay using AN/PSC-5 and SINCGARS radio sets. Retransmission may use analog voice (LOS onl

4 2. AN/CYZ-10 in key management mode. a. Turn on AN/CYZ-10. b. Select XMIT and press ENT. c. Select KEY and press ENT. d. Page-up or down to selec

58 Table 18 Retransmit ASIP Single Channel (SC) or Frequency Hopping (FH) SINCGARS Outstation A & B PT Voice PT Data CT Voice CT Data CO

59Perform the following procedure to send an Over The Air Re-key (OTAR). OTARs may be sent in VINSON mode using LOS or non-DAMA SATCOM. Equipment

60 Perform the following procedure to send an Over The Air Re-key (OTAR) in ANVDT mode using non-DAMA SATCOM. Equipment Required: KYX-15 Fill Cabl

61Perform the following procedure to receive an OTAR. OTARs may be sent in a VINSON mode using LOS or SATCOM or in ANDVT mode using SATCOM. 1. Ensu

62 Perform the following procedure to clone terminal parameters from one AN/PSC-5 to another. The radio will clone everything in the terminal exce

63The following footnotes are referenced throughout this manual (1). 1. Applies to message service only. Select manual to queue messages in termin

64 AC Automatic Control ac Alternating Current AK Automatic Keying BER Bit Error Rate BIT Built-In Test bps Bits per second BPSK Binary Phase Shift

65The following table lists satellite channels authorized for use with the radio set. Table 19 25-kHz Satellite Channels (1-8 are not applica

66 CHAN # DOWNLINK UPLINK CHAN # DOWNLINK UPLINK 77 261.725 295.325 118 263.800 297.400 78 261.750 295.350 119 263.825

67 The following table lists satellite channels authorized for use with the radio set. Table 20 5-kHz Satellite Channels CHAN # DOWNLINK UP

5The following procedure covers using the AN/CYZ-10 with CT3 software to load an orderwire key in position F2. See TM 11-5820-1130-12&P for oth

68 CHAN # DOWNLINK UPLINK CHAN # DOWNLINK UPLINK 203 243.955 317.055 223 244.105 317.205 204 243.965 317.065 224

By Order of the Secretary of the Army: ERIC K. SHINSEKI General, United States Army Chief of Staff Official: Adminis

PIN: 77443-000

6 d. Select DONE and press ENT. e. Select KYK-13 and press ENT. f. Select fill location (1-4) on AN/PSC-5. g. Arrow down on the AN/CYZ-10 h. P

7The following procedure updates a key. A key update is irreversible. NOTE: If the update count was exceeded the original key must be reloaded and